• Beware of Counterfeit Woodturning Tools (click here for details)
  • Johnathan Silwones is starting a new AAW chapter, Southern Alleghenies Woodturners, in Johnstown, PA. (click here for details)
  • Congratulations to Paul May for "Checkerboard (ver 3.0)" being selected as Turning of the Week for March 25, 2024 (click here for details)
  • Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.

CBN for Tormek

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
The grinding wheel on my Tormek is wearing down close to the minimum diameter and instead of getting a new standard grinding wheel I was considering the idea of getting a CBN wheel. The thing that had been preventing me from going ahead was that the available grits in a 10" wheel would mean settling for an edge that wasn't much better than what I could get by putting a CBN wheel on my dry grinder.

I was aware of the new higher grit CBN wheels that Woodturners Wonders had so while at SWAT last month I stopped by their booth and talked to Ken Rizza. He recommended the 600 grit wheel and invited me to see what I thought about the grind using a Tormek-like set up that he had in the booth. To me the results looked a lot like results on the Tormek wheel ... after roughing it up with the coarse side of the stone grader ... not what I wanted.

I told Ken that I wanted to run the wheel in water, but he recommended against doing that. I'll probably do it anyway since I don't like the nuisance of cleaning up the metal dust on my work bench. I understand the concern of corrosion due to dissimilar metals in contact so it will be important to not leave the wheel sitting in water when not in use.

I was leaning towards the 1200 grit wheel, but after more discussion decided to go with a 1000 grit wheel. After getting home I found that getting the old stone off was going to be a challenge. Even though I had updated it with a stainless steel shaft, there was a lot of rust that had frozen the wheel to the shaft. I finally was able to remove the wheel from the shaft after removing them together and using Vice Grips and a dead blow hammer along with a generous soaking of Aero Kroil, WD-40, and whatever else I thought might work. After cleaning up the shaft I saw a lot of pitting which seemed surprising for a shaft that was supposed to be stainless steel.

I ordered a new shaft and bushings, but my progress is temporarily stalled due to back surgery. After I get back up to speed, I'll resume my evaluation.

I have heard other turners say that the Tormek is too slow. As a hobby turner I turn at a leisurely pace, but even so, I don't see much difference in sharpening time between using a dry grinder and the Tormek other than the time it takes to sharpen a skew chisel. Anyway, I found this short Glenn Lucas video showing how slow the Tormek is when sharpening a bowl gouge: https://www.instagram.com/p/BNeh0SjBihY/
 

odie

TOTW Team
Joined
Dec 22, 2006
Messages
7,075
Likes
9,476
Location
Panning for Montana gold, with Betsy, the mule!
Well, I believe you, Bill......and, the short video from Glen Lucas was appropriate. I don't have a Tormek, but since I do all my honing by hand, I can relate to the hypothesis of it being quick. In both cases, we're basically discussing truing up an edge that's been previously ground, but needs the very tip of the edge re-sharpened. It's quick, if it's done precisely......and THAT point is what it seems many turners are not comprehending. :(

-----odie-----
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
Well, I believe you, Bill......and, the short video from Glen Lucas was appropriate. I don't have a Tormek, but since I do all my honing by hand, I can relate to the hypothesis of it being quick. In both cases, we're basically discussing truing up an edge that's been previously ground, but needs the very tip of the edge re-sharpened. It's quick, if it's done precisely......and THAT point is what it seems many turners are not comprehending. :(

-----odie-----

Some people like a more sawtooth like edge but I feel like that limits the final surface quality. Sometimes surface quality isn't as important when surface texturing will be done later. It's hard to make quantitative comparisons, but I believe that a smooth honed edge cuts longer than one that isn't.

I have sharpened tools on a dry grinder with CBN wheels and am impressed by the edge quality compared to sharpening with a matrix wheel.

I'm a little apprehensive about the results that I'll get with the CBN wheel. Even though it is 1000 grit, the surface feels rather rough compared to the standard Tormek wheel. I've heard Reed and others say that there is a break-in period for CBN wheels so I'm hoping that is true. Who knows, I may eventually decide to go back to using a Tormek stone.
 

odie

TOTW Team
Joined
Dec 22, 2006
Messages
7,075
Likes
9,476
Location
Panning for Montana gold, with Betsy, the mule!
Some people like a more sawtooth like edge but I feel like that limits the final surface quality. Sometimes surface quality isn't as important when surface texturing will be done later. It's hard to make quantitative comparisons, but I believe that a smooth honed edge cuts longer than one that isn't.

I have sharpened tools on a dry grinder with CBN wheels and am impressed by the edge quality compared to sharpening with a matrix wheel.

I'm a little apprehensive about the results that I'll get with the CBN wheel. Even though it is 1000 grit, the surface feels rather rough compared to the standard Tormek wheel. I've heard Reed and others say that there is a break-in period for CBN wheels so I'm hoping that is true. Who knows, I may eventually decide to go back to using a Tormek stone.

When you do do this, Bill.......I'm interested in hearing your findings. What are you planning to do with the upper surface of the flute on gouges?......you can't use the CBN wheel there. As you know, I've been using a round diamond hone there, and have been very happy with the results I've been having with it. If it weren't for the expense involved, I'd love to experiment with a 1000gt very slow dry wheel, in conjunction with hand honing the upper surface........:)

-----odie-----

edit: Agree fully that a fine edge is much more effective in producing a higher surface quality than the "sawtooth" that some turners seem to favor. The only advantage I see with it, is it's quicker to grind, without any further maintenance, and then return to your work. (.....but it's not necessarily quicker to true up an edge when the setup is in tune with that purpose, and done correctly.)

--o--
 
Last edited:

john lucas

AAW Forum Expert
Joined
Apr 26, 2004
Messages
8,321
Likes
3,576
Location
Cookeville, TN
Bill I find that my CBN 180 cuts just as fast as my 120 grit Aluminum oxide wheel or probably faster. I will go out in the shop in few minutes and grind a tool on it. Then I will go to my belt sander and find out what grit on the belt seems to match the quality of the CBN. That should be interesting. My on personal opinion, a well sharpened edge cuts cleaner and faster than a saw tooth edge. Now in all fairness I'm not roughing out a hundred bowls a week but it seems to work for Glen Lucas. I have been seriously thinking about changing my Tormek to the 1000 grit CBN. I never use the courser grit on the Tormek. I use the grading stone to sort of clean the wheel but not to purposely down grade the grit.
As far as quick sharpening. If you don't let it get dull it doesn't take any longer to sharpen on my Tormek than it does my grinder unless I need to take a lot of metal off. Ideally I don't let my tools get that dull. The only thing that takes time right now is to fill the water each morning and empty it at night. That is why I'm looking at the CBN. No water. You get very little dust when you are just cleaning up the edge on 1000 grit.
I would buy one sooner but I need new tires for the van and my 6 month insurance payment will be due shortly.
 
Joined
Aug 14, 2007
Messages
5,436
Likes
2,792
Location
Eugene, OR
I wouldn't run it in water. If dust is your concern, some thing I have been doing lately to try to combat that is to put some Trend lapping fluid on the bevel before I sharpen. This does keep the dust down at least a little, and keeps the wheel cleaner. My main problem with loading up on the wheel is from turning sloppy wet wood and a bunch of gunk gets on the wheel. The lapping fluid keeps the loading to a minimum, which really isn't much of a problem, probably just looks better...

The only concern I have with the really fine grit wheels is loading. Dave Schweitzer at D Way, and the Cutter Master/ Toycen or what ever up in Canada both expressed concerns about any thing over 600 grit tends to load up even if you are sharpening hardened metals on them. My first impression of the 600 grit wheel was exactly that, even before I heard it 'could' be a problem. With my 600 grit wheel, I continually make sure to put the lapping fluid on all bevels before I sharpen. In my latest sharpening video, I show where I take the Trend bottle, pop off the tilt/pop up lid off, double over a pipe cleaner leaving a finger ring in the middle and twist the ends together. This fits into the hole easily and gives just the right amount of fluid on the tool.

robo hippy
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
... What are you planning to do with the upper surface of the flute on gouges?....

I have an Alan Lacer diamond slipstone that is supposed to have a grit of 600 although after several years of use it feels more like 1000 grit. The radius on one edge very closely matches the flute of ⅝" bowl gouges and the small radius on the other edge is good for honing the flute of ⅜" bowl gouges.
 

john lucas

AAW Forum Expert
Joined
Apr 26, 2004
Messages
8,321
Likes
3,576
Location
Cookeville, TN
Bill I ran a test today. I sharpened a gouge on my 180 grit CBN and then tried several sanding belts. The grind looks very much like the grind I get from a new 180 grit belt. I have a worn 220 belt that definitely gives a finer finish. A new 320 grit belt cut faster but gave a finish appearance of my worn 220 grit belt. I remember when I took a class with Frank Sudol he used a 400 grit belt that he said was worn and cut like a 600. I was not good at sharpening in those days and had one heck of a time getting an edge on that "600" grit belt. I then sharpened one half of my spindle roughing gouge on the Tormek wheel. It's supposed to be 1000 grit but the finish still has lines and doesn't look all that much finer than the 320 grit belt gave me. Could be because I haven't used my grading stone lately. I've wondered if you wear away the finer grits with repeated sharpening and get a cut that is courser. Maybe if I remember tomorrow I'll grade it and try again.
 

RichColvin

Super Moderator
Staff member
OTI Member
Joined
Mar 13, 2016
Messages
667
Likes
497
Location
Marysville, OH
Website
www.colvintools.com
Bill,

There is a great review of CBN wheels on the Tormek forum. Here's the link :

https://www.tormek.com/forum/index.php?topic=3252.0

If you stay with the stone, I recommend the SB grindstone over the SG. The SB is much better with HSS, and I use mine often.

Kind regards,
Rich
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
Could be because I haven't used my grading stone lately. I've wondered if you wear away the finer grits with repeated sharpening and get a cut that is courser.

Just the opposite. The stone will get smoother and grind like 1000 grit.

Bill,

There is a great review of CBN wheels on the Tormek forum. Here's the link :

https://www.tormek.com/forum/index.php?topic=3252.0

If you stay with the stone, I recommend the SB grindstone over the SG. The SB is much better with HSS, and I use mine often.

Kind regards,
Rich

Thanks, I followed the evaluation of CBN wheels on the Tormek forum, but they were using coarser grit CBN steel wheels from D-Way. There's another thread where one of the members evaluated a higher grit (350 grit I think). Thanks for the recommendation on the blackstone wheel. I had been considering it for a number of years.
 
Joined
Apr 1, 2015
Messages
603
Likes
443
Location
Sitka, Alaska, United States
Website
www.zachlaperriere.com
Now this conversation is getting really interesting! I agree that a fine edge cuts much cleaner than a sawtooth edge.

Over the last couple of years I've gone for the two extremes in sharpening...I do all my roughing with a 60 grit CBN wheel (it was 80 until fairly recently, but the 60 is a bit faster for shaping the secondary non-rubbing bevel) and all of my finish work is sharpened at 800.

Robo is right that the finer grits load up. I'm not a production turner, around 150 bowls a year, and the 800 grit is holding in there after a year—though it's about time to soak and clean again. Previously I sharpened for a year or so at 1000 with one of Ken's wheels, though I switched to Dave's 800 wheel after the 1000 seemed to be staying a little loaded. It's possible I just didn't clean the 1000 well enough. I've never used a lapping oil, though it seems prudent.

Because I use on Michaelsen grind, I only ever sharpen around a 1/16" of bevel with the finer grits, so the gouge only gets a light pass on the 800. I could see where a full bevel at higher grits would load fairly fast.

I'd really like to see more research and/or compare notes on getting wheel unloaded. Dave suggested soaking then scrubbing with a strong soap that would break down the wood resins that might be causing some of the loading.
 
Joined
Jul 26, 2016
Messages
2,326
Likes
1,105
Location
Nebraska
Novozymes produces a large number of enzymes used in every industrial, commercial and retail product
on the market today. They produce custom engineered enzymes that will break down just about any
material needing to be cleaned from a surface. Dish detergents have small amounts of specific enzymes
used for the task, they make a number of concentrated products that are used in other industries that may
speed up the process for cleaning grinding wheels.
 
Joined
Aug 14, 2007
Messages
5,436
Likes
2,792
Location
Eugene, OR
My fine wheels 'appear' to have some loading, but they still cut fine. More experimenting needed.

I guess one interesting thing for me is that my 6+ year old 180 grit wheel leaves a very polished surface, especially when compared to a new 180 grit wheel, though I really don't notice a difference in how they cut...

robo hippy
 
Joined
Apr 1, 2015
Messages
603
Likes
443
Location
Sitka, Alaska, United States
Website
www.zachlaperriere.com
I thought to share an experiment that probably doesn't need repeating! Regarding the difference in burrs created by a CBN wheel, I thought I'd try sharpening with the wheel going in reverse. So I sharpened a handful of 1/2 and 3/8" gouges on the backside of the grinder, which of course means that the wheel was spinning up, rather than down and toward the cutting edge.

The sharpening created a burr that at the end was long and could be broken off when I looked up close. Under a 20 power microscope the edges looked similar once this burr had been broken off.

When cutting wood I found that the reverse ground tool appeared to be as sharp as the normal grind for the first half inch or so of cutting then the edge went to pot. I went through a dozen or so reverse sharpening before I completely gave up.

EDIT: I only tried with 800 grit, so this could skew the results, and I only tried with one a fingernail grind somewhere around 50 degrees.
 
Last edited:
Joined
Aug 14, 2007
Messages
5,436
Likes
2,792
Location
Eugene, OR
Interesting Zach.... I know Jimmy Clewes prefers a reverse/up side down sharpened scraper burr for his clean up cuts. I would think that the burr would fall off quickly than the tool would cut as normal rather than be more blunt...

robo hippy
 

john lucas

AAW Forum Expert
Joined
Apr 26, 2004
Messages
8,321
Likes
3,576
Location
Cookeville, TN
Interesting Zach. I have a belt sander and have been playing with sharpening on it to see what the advantages and disadvantages are. I have the belt running up so essentially in reverse. I don't notice a bit of difference in how the edge holds up. What I have notices is that when I use the 320 belt instead of 180 it holds an edge longer. On my bowl gouges not so noticeable but on my spindle roughing gouge on dry wood it's noticeably longer.
 
Joined
Apr 1, 2015
Messages
603
Likes
443
Location
Sitka, Alaska, United States
Website
www.zachlaperriere.com
@robo hippy @john lucas I forgot to mention that my little experiment was on my 800 grit wheel.

The results surprised me, too. But on the other hand, when sharpening knives, everyone I know suggests either sharpening in circles or sharpening toward the edge, especially at the higher grits.

Why the edge failed on the gouge so fast defies any explanation I can come up with.

John, that's pretty interesting that the 320 belt hold an edge longer than 180. I can't say for certain, but I'll echo what Robo and others have said that a finer grit CBN edge doesn't last as long as a courser grit. There's just so much to learn.
 
Joined
Oct 29, 2014
Messages
469
Likes
90
Location
nj
. After cleaning up the shaft I saw a lot of pitting which seemed surprising for a shaft that was supposed to be stainless steel.

Stainless steel is not what it's cracked up to be. Leaving aside the dozens of grades of stainless some magnetic - some not, Some weldable - some not, some can be heat treated - some not. Different SST tolerates different kinds of acids - yadda yadda yadda. One thing is a constant. Stainless Steel is only Stainless because of the Chrome Oxide layer on the surface that results from Chromium migrating (yah - swimming like a fish through the metal) to the surface and interacting with the O2 in the air. Then it becomes Chrome Oxide. When it's underwater in an Oxygen deprived solution the Passive Oxide layer can become depleted and corrosion can set in. That's why one doesn't use SST screws for boat-building. Low O2 in a bay or estuary will cause the SST to rust. Now Inconel is altogether different. But no one sells shafting in Inconel.

All that said. I've always wondered something about CBN wheels:
How Long do they last?
 
Joined
May 14, 2004
Messages
29
Likes
0
Location
Central Illinois
I bought the 10" Grizzly wet grinder took the wheel off and replaced my Tormek stone. I then put a 600 CBN on the Griz. The Griz turns a little faster than the Tormek. Grizzly stone is 1200 grit.
 

john lucas

AAW Forum Expert
Joined
Apr 26, 2004
Messages
8,321
Likes
3,576
Location
Cookeville, TN
Raul I don't know how long the CBN wheel's last. Mine is over 3 years old and still working perfectly.
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
I bought the 10" Grizzly wet grinder took the wheel off and replaced my Tormek stone. I then put a 600 CBN on the Griz. The Griz turns a little faster than the Tormek. Grizzly stone is 1200 grit.

So you were using a Tormek stone on the Griz? ... And, then replaced it with the CBN wheel? Do you like the 1200 grit?

At first I was a bit disappointed with the 1000 grit CBN wheel being too coarse, but it seems to be "wearing in" after initially shedding a lot of excess CBN crystals.
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
Update on using the CBN wheel on the Tormek:

  • Since the old shaft on the Tormek had a small amount of corrosion pitting and was worn slightly from rubbing the plastic bushings (the plastic bushings were well worn), I ordered a new shaft kit that included new bushings, drive pin, drive wheel washer, precision machined washer for the grindstone, and EZ Lock nut for changing grindstones without tools.
  • Since my Tormek is approaching its twentieth birthday, I went for a total makeover and got a new drive wheel and a new leather honing wheel.
  • The new drive wheel is metal instead of plastic ... not that there was anything wrong with the old plastic wheel except that the rubber was starting to harden a bit and develop a slight glaze on the surface.
  • The old leather honing wheel had a nice glossy black patina, but also had a pronounced dip worn in the middle.
  • The first thing that I discovered when installing the CBN wheel was that it rubbed against the housing. The reason is that the hub of the CBN wheel is recessed 3/16 inch on both sides whereas the Tormek grindstone is recessed only on the outboard side. So I had to hunt for a sufficiently thick flat washer that was uniform in thickness. I'm still experimenting with different washers, but I think that I will go with a ⅛" thick.nylon washer.
  • Initially, I used the wheel dry, but didn't like a the dust scattered everywhere. I also didn't like the rough bevel that the CBN wheel produced.
  • I have been using the CBN wheel wet and like that much more than dry.
  • I tried the blackstone wheel to see how well it would work sharpening a bowl gouge. The finish is nearly as good as the standard gray stone. The blackstone is also supposed to be good for touching up carbide cutters.
  • It has been a month since my back surgery, but I still haven't been cleared to do any turning. All my tools are sharp and just sitting there. sigh
 
Joined
Jan 9, 2011
Messages
63
Likes
31
Location
Englishtown, NJ
Bill, I saw this one before signing off. It is late, my lady needs a ride at noon, so I'll open just one more beer.

I had a Tormek wet 10" a for a while, I gave it to my AAW chapter when I got a CBN wheel for my 8" dry grinder. The available jigs for the dry grinder are better, in my opinion, than the Tormek jigs. The slow speed of the Tormek does allow for small adjustments in the grind, but I found that the time to get an edge, even if just duplicating it, was excessive on the "slow/wet". As my shop is in my bedroom I don't have room for a lot of tools - my choice was to give the "slow/wet" away and go with a variable speed 8" grinder. I have no regrets. My CBN wheels are D-Way, with the "fine" (180, I think) wheel having the rounded edges for making my cutters, and my coarse wheel having a small grinding edge on the sides.

When my "slow grinder" died I bought a standard Delta VS to replace it, a lot cheaper than the 1750 "slows". It has a low rpm of 2200, and a high of 3400. At 2200 the CBN wheel gives me a clean edge comparable to the Tormek slow/wet and the 1750 slow with a fine grit high grade AO wheel.

Tonight I was working on reshaping some tools, I reground them to shape with the Delta VS grinder at the top (@ 3400) and had no problem with overheating of the M2 steel. I dropped the speed to refine then, then, using the same jig, moved over to the fine wheel to refine them.

Unless one wants a concave bevel from a 10" wheel, which you will only get when the wheel is new, I see no advantage to the Tormek "slow/wet". I loved it when it was my only alternative in shaping my tools as I wanted them, but times change and so do the devices.

Contact me directly via email, if you would like - I'd prefer to offer the details directly. The email address, with the symbol substituted by the word in quotes, is jon"at"murphsays.com.
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
Bill, did you get the aluminum wheel or the new Spartan nylon one?

The wheel that I have is the aluminum Tornado (4 in 1 style). I don't like the Spartan design because it doesn't have grit on the side. Also the narrow hub on the Spartan wouldn't work well with the EZLock nut.

The aluminum wheel is surprisingly heavy ... very close to the same weight as the AlO wheel ... maybe even heavier.
 
Joined
Aug 14, 2007
Messages
5,436
Likes
2,792
Location
Eugene, OR
Bill, what do you use the side grind feature for? I prefer the straight wheels without the radius edge. I don't think I have any particular use for a flat bevel, but then have never used one either...

robo hippy
 

john lucas

AAW Forum Expert
Joined
Apr 26, 2004
Messages
8,321
Likes
3,576
Location
Cookeville, TN
I use the side grind with slightly rounded edges to grind my hollowing tool cutters. They are 3/16 square HSS. Learned that technique from Lyle Jamieson. You sort of pull the left side of the tool across the right hand radius of the stone. then do the same to the right side of the tool pulling it up and over the left hand side of the stone and the round over the nose. Gives you an edge that looks a lot like a bowl gouge but without the flute of course.
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
Bill, what do you use the side grind feature for? I prefer the straight wheels without the radius edge. I don't think I have any particular use for a flat bevel, but then have never used one either...

robo hippy

I use it for several things:
  • flattening hand chisels
  • flattening hand planes
  • gently flattening the top of scrapers to knock off the raised burr.
I should mention that this is on a 1000 grit stone or CBN wheel running at only 90 RPM so it is more like hand honing and not comparable to what you would do with a grinder with a 180 grit wheel running at 1750 RPM. Since I'm working on a large surface area it's more like polishing the surface flat and not grinding away much metal.
 
Joined
Aug 14, 2007
Messages
5,436
Likes
2,792
Location
Eugene, OR
Hmm, I do know the radius edge was a David Ellsworth idea, and the hollowing bits are apparently easier to sharpen with the rounded edge. Never considered using the side to hone off the scraper burrs, always did that by hand. Same with chisels and plane irons. The slow speed of the Tormek would make this a good use if the side grind was a couple of inches long/wide.

robo hippy
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
Hmm, I do know the radius edge was a David Ellsworth idea, and the hollowing bits are apparently easier to sharpen with the rounded edge. Never considered using the side to hone off the scraper burrs, always did that by hand. Same with chisels and plane irons. The slow speed of the Tormek would make this a good use if the side grind was a couple of inches long/wide.

robo hippy

I should clarify what the wheel looks like. It is 2" wide with square corners on the edges and then It's 1" wide on the sides ... no rounded corners. The way that a tool is presented at an angle on the side of the wheel, you have the equivalent of a wider grinding surface ... and by moving the tool quickly side to side you can actually flatten an even wider surface.
 
Back
Top