• Beware of Counterfeit Woodturning Tools (click here for details)
  • Johnathan Silwones is starting a new AAW chapter, Southern Alleghenies Woodturners, in Johnstown, PA. (click here for details)
  • Congratulations to Paul May for "Checkerboard (ver 3.0)" being selected as Turning of the Week for March 25, 2024 (click here for details)
  • Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.

Applying finish while on the lathe

Joined
May 5, 2017
Messages
137
Likes
16
Location
Saint Louis, Missouri, USA
From various videos I see that most people apply a finish while the item is on the lathe. Yesterday I was watching a DVD (Bat Houses by David Best) and he was using a painters brush to apply lacquer. Although he covered up the ways with a paper towel it looked like he got the lacquer on the chuck jaws.

Would a finish getting on chuck jaws cause problems? I am wondering about finish buildup not allowing the jaws to expand correctly into a recess.
 

hockenbery

Forum MVP
Beta Tester
TOTW Team
Joined
Apr 27, 2004
Messages
8,592
Likes
4,889
Location
Lakeland, Florida
Website
www.hockenberywoodturning.com
I finish all of my bowls and hollow forms off the lathe. I also finish the sanding of most off the lathe

Smaller items I finish on the lathe.
Hollow ball Christmas ornament balls and finials get their first coat on the lathe then more coats after they are glued together.

I try to a void getting finish o the chuck. A little on the outsides of the jaws is harmless.
Finish Inside the jaws or on top of the jaws will cause misalignment of the work piece.
Finish on the scroll gears will cause the chuck to not open and close smoothly or not move at all if there is a lot built up.
Be careful. Also clean the jaws when you get them gunked up.
 
Joined
Jul 26, 2016
Messages
2,326
Likes
1,105
Location
Nebraska
If you take the time to protect the lathe bed ways you can also take a few seconds to protect
the chuck from getting finish on the jaws which may get into the scroll if you get carried away
with the liquid finish brushing it on the piece.
Your other option is to recognize that you may get contaminates on the lathe and chuck and you
may need to take time to clean these on a regular basis. On occasion I may have limited time to
get a number of pieces completed in a specified time so I take short cuts while applying finish when
certain products can be finished on the lathe. This allows me to get the order out the door on a timely
basis and when time allows I will clean up the lathe and tools that were compromised.
Trying to open and close a gummed up scroll chuck is no fun, and sliding a tail stock down a gummed
up lathe bed can cause injury to a person on a bigger lathe when the heavy tail stock does not slide smoothly.
Anyone with shoulder problems, tennis elbow or arthritis will know how this can be painful.
 
Joined
Oct 25, 2005
Messages
935
Likes
241
Location
Newberg, OR: 20mi SW of Portland: AAW #21058
Would a finish getting on chuck jaws cause problems? I am wondering about finish buildup not allowing the jaws to expand correctly into a recess.

Sloppy applications of finish materials won’t hurt the chuck at all and, I’d imagine, it would take quite a few applications to affect a mortise fit. However, if such a thing were to occur, you could soak the jaws (or even the entire chuck) in solvent with no ill effects.
 

Bill Boehme

Administrator
Staff member
Beta Tester
TOTW Team
Joined
Jan 27, 2005
Messages
12,886
Likes
5,169
Location
Dalworthington Gardens, TX
Website
pbase.com
When I was a beginner I used friction finish (Hut Crystal Coat), but now I do all my finishing off the lathe and outside of the shop. Sometimes the chuck is still attached ... and when it is I cover the chuck with wide painters tape.
 

john lucas

AAW Forum Expert
Joined
Apr 26, 2004
Messages
8,321
Likes
3,576
Location
Cookeville, TN
I can't imagine brushing on a finish unless I was going to wipe it down. I don't like thick finishes unless the finish has been finished so it looks like glass. I wouldn't want to have to clean the jaws. I apply a wipe on finish like minwax wipe on poly while it's on the lathe. It's such a fine finish it would take a huge amount to cause problems with build up on the jaws. I usually apply one layer while on the lathe and then apply several more off the lathe. I could imagine brushing on an oil finish, let it sit and then wipe it out.
 
Joined
Jan 18, 2006
Messages
101
Likes
47
Location
Pueblo West, CO
I finish just about everything on the lathe, but apply the finish with a paper towel. If some gets on the chuck jaws it easy to clean by closing the jaws, reducing the speed and apply some sandpaper. Never had any finish get to the inside jaw faces. A leg from a pair of worn out pants or piece of cardboard cut to size works well to cover the bed. Allyn
 
Joined
Jan 24, 2010
Messages
3,058
Likes
900
Location
Cleveland, Tennessee
I still wear them. ;)
With the finishing thread, the AAW magazine had an outstanding article for "Bulletproof Pen Finishes" by Kurt Hertzog in the February, 2017 issue. I now apply the CA to my pens with one hand while turning the blank manually. Works for me.
 

odie

TOTW Team
Joined
Dec 22, 2006
Messages
7,076
Likes
9,487
Location
Panning for Montana gold, with Betsy, the mule!
I finish just about everything on the lathe, but apply the finish with a paper towel.

I used to use paper towels, too.....but, stopped doing this some years back. There really isn't anything you can do to prevent the paper towel from breaking down during the application. Tiny little bits of the paper will become lodged in the grain, within detail grooves, and any other opening in the wood. I use nothing but cotton cloth for application purposes now. Specifically, 3" square cotton shotgun cleaning patches......available at your local sporting goods store. Use them, then toss them! :D

-----odie-----
 
Joined
Jul 26, 2016
Messages
2,326
Likes
1,105
Location
Nebraska
They do make lint free wipes which are used in clean rooms and industrial applications
where paper towels won't work. These are stronger and more cloth like material which
absorb liquids readily.
 
Back
Top