FS: Barracuda Micro Lathe Chuck, Jaws $50 + shipping

Discussion in 'Marketplace Archives' started by Mark Hepburn, Nov 15, 2016.

Thread Status:
Not open for further replies.
  1. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    EDIT: I've cleaned and shined it up and added a couple more photos.

    This is a small, Barracuda Micro key operated scroll chuck I've had and used for a while. I have three of the Barracuda 2 chucks that I like and use a lot for smaller work but will be replacing as I move up to the Vicmarc 120s over time.

    So, I do like this chuck but am going a different direction and so am hoping to sell this and another chuck. It's mechanically sound with zero issues, but does have some blemishes.

    It is complete as purchased (minus the blow-molded case, which I threw away a while back). It includes the chuck, key, hex wrench, 3 sets of jaws, extra screws and the screw chuck.

    Here are the specs on the jaws:
    Included Jaws: Pin,#1,#3
    Pin Jaw Grip: Internal: 7/8" to 1-5/8"
    #1 Step jaw gripping: External: 1/16 to 13/16"
    Internal : 5/8 to 1-3/4"
    #2 Standard Jaw gripping: External: 3/32" to 1-3/8"
    Internal: 11/16" to 2-3/8"


    Bought for $130. Asking $55.

    I'll ship however you like. The chuck weighs about a pound and the rest of the items probably another pound.







    IMG_5440.JPG IMG_5441.JPG IMG_5442.JPG


    IMG_5423.JPG IMG_5424.JPG
     
    Last edited: Nov 16, 2016
  2. Barry Crowder

    Barry Crowder

    Joined:
    Mar 12, 2016
    Messages:
    74
    Location:
    DFW, TX, USA
    Does that have 1"-8tpi threads? Also, is that rust on the chrome pieces, or some kind of residue?

    I'm on the fence because it's similar to the one I have already, but it would be nice to have a spare with different sized jaws installed...
     
  3. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Barry,

    It's 1" x 8 tpi threads. the color is some transtint orange.
     
  4. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Barry, I'll clean it up some more before I send it out. I just didn't think of it to tell the truth. I'm like you: I have a few of the other chucks so I have the jaws already installed. If only I could do that with the Vicmarcs!
     
  5. Jamie Straw

    Jamie Straw

    Joined:
    May 28, 2015
    Messages:
    1,440
    Location:
    Bainbridge Island, WA
    Mark, if Barry decides not to get it, I might be interested.
     
  6. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Thanks Jamie. So far, no takers. I did clean it up and no rust. :)
     
  7. Barry Crowder

    Barry Crowder

    Joined:
    Mar 12, 2016
    Messages:
    74
    Location:
    DFW, TX, USA
    FWIW, I haven't committed, and I understand that it's first come, first served.
     
  8. Jamie Straw

    Jamie Straw

    Joined:
    May 28, 2015
    Messages:
    1,440
    Location:
    Bainbridge Island, WA
    Barry, you're welcome to "first dibs." If you decide "nope," I'll take 2nd, no hurry for me (but not speaking for Mark:))
     
Thread Status:
Not open for further replies.

Share This Page