FS: Thin stock ripping jig for table saw

Discussion in 'Marketplace Archives' started by Mark Hepburn, Nov 17, 2016.

Thread Status:
Not open for further replies.
  1. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Update: I'll pay the shipping, asking twenty dollars

    I continue to purge my shop of things that I know I won't be using to buy toys that I will :)

    This is a Fulton thin rip tablesaw jig

    I got this it some time ago as a gift from my dearly beloved and never used it. It won't fit my slider, which has a non-standard T-slot, and I'M not going to tell her. Perhaps someone can use this. Still in the box and never used. Im asking $20 and will pay postage in the US.

    It sells over at Peachtree for $29.95.

    Thanks,

    Mark


    IMG_5446.JPG IMG_5448.JPG IMG_5449.JPG
     
    Last edited: Dec 4, 2016
  2. Mike Johnson

    Mike Johnson

    Joined:
    Jul 26, 2016
    Messages:
    618
    Location:
    Nebraska
    What is the width of the slider guide?
     
  3. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Mike, it's a 3/4" T-slot. Here are some photos of the dimensions

    IMG_5460.JPG IMG_5459.JPG


    IMG_5458.JPG
     
  4. Jamie Straw

    Jamie Straw

    Joined:
    May 28, 2015
    Messages:
    1,440
    Location:
    Bainbridge Island, WA
    Hi, Mark, I sent a reply to your "Conversation" on 11/26 (about one of the chucks), haven't heard back from you. Please LMK what the status is. Thanks
     
  5. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Jamie, I just sent a reply. Sorry about the delay.
     
  6. Jon Minerich

    Jon Minerich

    Joined:
    Dec 26, 2011
    Messages:
    28
    Location:
    Biloxi, Mississippi
    Mark, if it isn't sold, I will buy it. Thanks, Jon
     
  7. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Thanks Jon.

    If you'll PM your address I'll get it out to you today if I can. Tomorrow for sure if not today
     
    Last edited: Dec 23, 2016
  8. Jon Minerich

    Jon Minerich

    Joined:
    Dec 26, 2011
    Messages:
    28
    Location:
    Biloxi, Mississippi
    Mark, my apologies. I was busy with family during Christmas. Now for my embarrassment, how do I PM you?
     
  9. Mike Johnson

    Mike Johnson

    Joined:
    Jul 26, 2016
    Messages:
    618
    Location:
    Nebraska
    Jon,

    If you click on Mark Hepburn there is an option to "Start A Conversation".
    The message will show up in his message box.
     
  10. Bill Boehme

    Bill Boehme Administrator Staff Member

    Joined:
    Jan 27, 2005
    Messages:
    8,125
    Location:
    Dalworthington Gardens, TX
    Home Page:
    What Mike Johnson said.

    Our forum software uses the word Conversation to mean the same thing as the term Personal Message. That is confusing. We switched over earlier this year from a different forum software that used Personal Message and we're shifting our paradigms to the new terminology which still seems a bit odd after so many years of being accustomed to the previous terminology.
     
  11. Jon Minerich

    Jon Minerich

    Joined:
    Dec 26, 2011
    Messages:
    28
    Location:
    Biloxi, Mississippi
    Thanks Bill!
     
  12. Mark Hepburn

    Mark Hepburn

    Joined:
    Mar 26, 2014
    Messages:
    1,170
    Location:
    Houma, Louisiana
    Jon, Bill:

    Sorry to take so long to reply here. Thanks for picking up my slack Bill.

    Sold and shipped to Jon. Thanks!
     
Thread Status:
Not open for further replies.

Share This Page