Carbide tools + RPM

[Jordan Daoust]

Good morning!
I've been turning for just over a year, I use Rockler's 12-24 midi lathe and carbide turning tools. I've had a lot of success and have turned some beautiful pieces.

I mainly turn bowls/platters/boxes etc. usually less than 10" in diameter and 16" in length.

Here's where I want some feedback from the hive mind: When i'm turning, I find myself trying to get to the top rpm (~1,200) as quick as possible so I can turn efficiently and get a smooth finish although, I very often have to start at 80 grit when sanding and usually spend more time sanding than turning. I keep my carbide tools fresh and sharp as much as I can.

Thoughts? Advice?

 

[Alan Weinberg]

Not sure what type of carbide you use, but most are just scrapers. My advice, 3 years in, is to learn how to turn with traditional tools—gouges. Look at Hunter carbides if you decline to try gouges. And reaching 1200 rpm is not necessarily the goal—depends on wood type, wood shape, blank size. Find a mentor and join a group.

 

[Bill Alston]

There are a series of YouTube videos where one turner shows you how to cut rather than just scrape with carbide tipped tools. Here’s just one.

View: https://youtu.be/eUO98R-8JgI

 

[Robert Santore]

Here's where I want some feedback from the hive mind: When i'm turning, I find myself trying to get to the top rpm (~1,200) as quick as possible so I can turn efficiently and get a smooth finish although, I very often have to start at 80 grit when sanding and usually spend more time sanding than turning. I keep my carbide tools fresh and sharp as much as I can.

Are you having problems with certain types of wood, or is it across the board?

What issues are you sanding out? Is it tearout / end grain or are you seeing the same issues across the entire surface? You didn't mention spindle work but do you see the same issues? Understanding where things are going wrong might give you a good clue as to what you need to fix.

I've only been turning a few years myself but one thing that helped me a lot was to use every pass as a practice cut and diagnose what was happening, what worked and what didn't. Make a pass, stop, and evaluate. Don't wait to be at your final form before stopping and seeing how you're doing, cause at that point sandpaper is your only recourse.

I haven't tried carbides, and so my bag of tricks won't be helpful for you. But, things I play with are tool choice, sharpness, angle of presentation, bevel support, how aggressive the cut is. Play around and see if you can make incremental improvements.

 

[Jordan Daoust]

The main issue seems to be end grain tearout, Some woods have more "damage" than others, but it seems to be a recurring issue that i've been having.

I'll definitely start watching those videos, thank you for posting!

I took a class at WoodCraft and learned on traditional tools, but when it came to getting my own setup up and running, I chose carbide. I am definitely not against traditional tools, and I know they will be in my future, the only barrier is cost at this point.

 

[robo hippy]

The carbide tools are mostly used as scrapers, and while they do work, you still need gouge and skew skills. With scrapers and experience, you can get excellent results on end grain pieces, but on bowls, they leave a LOT to be desired, which is mostly tear out which requires a lot more sanding time. I don't think I have met any one who actually likes to sand. I sure don't. As for speed, there are all sorts of formulas. Since my first lathes had no rpm read outs on them, I learned to turn by speed. With bowls, I would not go much over about 1000 for a 6 inch diameter bowl, but that may be too fast, especially for a beginner. Spindles are usually done much faster, in the 2000 rpm range, and again, it depends on size. It is a feet/minute thing. Small spindles, as fast as your lathe can go, maybe. Rolling pin about 2 inch diameter, not more than 2000 rpm. Bowls, in the 600 to 1000 range, and all of this depends on the wood. I do not turn crappy wood, though some love the channelge.

robo hippy

 

[Curt Vogt]

I took a class at WoodCraft and learned on traditional tools, but when it came to getting my own setup up and running, I chose carbide. I am definitely not against traditional tools, and I know they will be in my future, the only barrier is cost at this point.

This is what I usually told new/prospective woodturners when they were looking at a big display case full of shiny new woodturning tools:

If I had the proverbial one tool to use when I am stuck on that desert island...
3/8" Bowl Gouge for the win.
I think it has the biggest bang for your $.

Second is a 1" Skew. The first one you get I would lean towards one with square shape on the bar stock as opposed to oval.
But man, do I sure enjoy my oval skew when doing my long spindles and finials!

I know many folks here will highly recommend some premium tools with corresponding premium prices...
but a bargain-basement High-Speed Steel (HSS) tool still works and can get you started.
Save your money on the turning tool side if you need to also budget in a grinder for sharpening.
Learning how to sharpen what you have and what sharp can do for you at the lathe is not a bad thing.
The only thing about lower cost tools is they do not generally have a refined shape. But go for it anyway!

 

[Bill Alston]

One thing I’ve noticed is that there seem to be quite a few bowl turners on here that use power sanders, so you’re not alone Jordan, and I’m guessing many if not most are using conventional tools?

Have a look at Glens videos where he uses Cupped Carbide inserts. He seems to achieve a very good finish with them.

 

[John K Jordan]

I find myself trying to get to the top rpm (~1,200) as quick as possible so I can turn efficiently and get a smooth finish although, I very often have to start at 80 grit when sanding and usually spend more time sanding than turning. I keep my carbide tools fresh and sharp as much as I can.

Carbide tools have some advantages, such as when sharpening.

But my advice is to ditch any carbide tools that work like scrapers. Using them on most wood will require significant sanding.

I also recommend the "traditional" tools. But if you don't want to sharpen and use traditional gouges, skews, etc, take a look at the Hunter carbide tools. My favorite is the Hercules. Hunter tools have razor-sharp round cutters that work just like a sharp gouge. You don't sharpen them but rotate the cutter a little occasionally to spread the gradual wear around the circumference. They are used just like a spindle or bowl gouge. Can make an extremely clean cut. When the cutter eventually wears out you replace it with a new one. The first cutter on my Hunter Hercules stayed sharp a LONG time - can't remember now, maybe a year?

I often use Hunters on spindles, bowls, platters, almost everywhere except where I need to get into tight "corners" or v-grooves. You CAN use Hunter tools as scrapers, flat on the rest, but that would be such a waste of a clean cut! A bonus advantage when turning a bowl is the cutter throws hot chips to the side while a bowl gouge guides them directly to my hand. And by doing the initial surface smoothing with hand scrapers on bowls and platters I can usually start sanding with 400. (I have one piece I sometimes show at demos that has been touched only by 600 grit.)

Using Hunters I can often start sanding with 400 grit or finer (with good hard wood). For example, this shows the surface right off the tool from the 1st finishing pass with a Hunter Hercules - I think I started sanding this at 600 grit. (Of course, this is hard, fine-grained African Blackwood. Something softer or turned without a steady hand may require more sanding.) BTW, I quit using power sanding on anything so many years ago I can't remember the last time. I don't like the clouds of dust and what the rotating disks can do to the wood. IMO, there are better ways. (I do have a close-quarters drill in a drawer by the lathe but I only use it for, well, drilling in close quarters. )



The picture above shows the handle section I made for this, assembled after turning some acrylic pieces and doing a bit of carving on the ends of each section.


JKJ