• August 2025 Turning Challenge: Wooden Version of Non-Wood Item! (click here for details)
  • Congratulations to Nino Cocchiarella for "Three Sisters" being selected as Turning of the Week for August 18, 2025 (click here for details)
  • Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.

mounting large turnings on the lathe

Joined
Jul 21, 2008
Messages
166
Likes
7
Location
Staunton, VA
How do you mount your large green blanks on the lathe? I have always used my oneway big bite spur drive and tailstock support, with the bowl mounted towards the headstock and the foot towards the tailstock. Shaping the bowl is easy enough, but turning it around to mount in my stronghold chuck is not! I have the #4 Oneway jaws, but turning around a blank that weighs over 50lbs is next to impossible to perform without there being significant eccentricity when remounted. While coring a big 13x10" deep bowl I had a catch with the McNaughton which sent the blank flying across my shop. I need a better solution for large blanks. I've considered using a glue block and parting it off when complete, but how would one accomplish this? What do you do in this situation? I'm thinking about using CA glue and a big glueblock, utilizing a 3" electric planer to smooth out a spot to mount the glueblock and faceplate. But wondering how to accomplish this in a safe fashion. I want to know how others take on this mounting.
 
You could use a faceplate and glue block. I use 6" dovetail jaws for a bowl that size. If you can, especially when using the McNaughton system, make your tenon at least 40 percent of the diameter of your bowl.
 
I need a better solution for large blanks
Consider using a faceplate. On a bowl that big you should be able to incorporate the faceplate mounting tenon in the blank.
I use a faceplate on most hollow forms.

Turn a tenon larger diameter than your faceplate by 1/2 to 1” and 1/4” taller than the screw length sticking through your faceplate.
This size lets to drive screws into wet wood without splitting out the edge and screws will open up the wood a little bit deeper that they ar long but not a 1/4”


Slightly concave the surface of the tenon. This ensures the faceplate won’t rock and the outer edge of the faceplate makes nice contact.
I use a pencil to draw circles and use those to line up the faceplate nicely
You can also turn a center tenon the diameter of the faceplate threads and use it to line up the threads. This tenon can keep the faceplate from screwing on.


Here is a video clip from a demo where I mount a faceplate on a hollow form to be.

 
Last edited:
I do 20-25 inch bowls regularly. I core whenever possible. I start with a oneway 6 in faceplate attached to the blank face (future bowl hollow side) using the tailstock work the outside of the bowl blank till satisfied and turn the tenon at the same time. Ensure the center point of the tenon is well marked for later use. For blanks this large I use #5 0r #6 stronghold jaws. Turn blank around, core and wait about 1 year to finish (bummer but necessary) Realize that the bowl blank will warp ,maybe even go oval. the second turning will require rounding the tenon again hence the well marked center point I jam chuck the bowl blank with the tenon on the tailstock side re-round the tenon, reverse the blank using a chuck now and turn a bowl. Hope this is understandable and helps. Ray
 
For getting big stuff onto the lathe, I use a hoist. Very simple, very cheap and works a treat.

This picture of the hoist was a proof of concept with my new hoist. The hoist is mounted on one of the roof girders on a sliding rail, which came off a around the world sailing boat.

As my lathe is on wheels, I just locate it under the timber and mount it, then for turning around I use the hoist again and again until the blank is small enough for me to handle.

I also use Vicmarc Faceplate rings, there are four sizes, they are light but very strong.

Hoist_For_Blanks_Web.jpg

2436_690mm_Diagonal_Blank_web.jpg

600mm_Wet_blank_Web_002.jpg
 
I'd agree with the faceplate users for the mount, and some sort of ground-based hoist to lift. There are versions of engine lifts you could utilize. I'd not suggest ceiling mounted hoists, nearly all garage roof framing (such as wood trusses or hand framed rafters and joists) is not built to handle the concentrated loads of a hoist system and the loads they lift, keep the weight on the ground with something like this-
They have lifting straps shown in the similar hoist product catagory.

And for weight like this, I would never consider a glue joint, CA or wood glue. CA easily fractures, and with moist wood regular wood glue would not likely cure properly.
 
Last edited:
Heavy blanks can be a challenge to get mounted singlehandedly, but I've discovered a couple tricks that make it easier. I have a couple choices of drive options available: An Elio drive and a big spur drive that fits into my 50mm chuck jaws. I have no recollection of who made the spur drive or where I got it, but it tends to get more use because the Elio requires use of an Allen key to bury the pointed machine screws. (I keep thinking I should replace them with pointed flange bolts and keep the proper size Gear Wrench handy)

For either use of either drive, I start by choosing a center point. Big blanks are too heavy to try to find a balance point, so it's estimated, or if the size of the piece dictates it, the center point is dictated by measurement. It can be on the cut face or the bark side, you just have to start somewhere. It can always be changed/adjusted later. I use a Forstner bit to drill into the blank a bit. This not only provides a solid grip point, but provides a shoulder to sort of "hang" the blank on the drive point, while the other hand brings up the tailstock.

As far as your piece not running true when you flip it around, are you making a random size tenon? I used to see chuck jaws as having a range of allowable sizes, which is true, but to flip a piece and have it run true, (or very close) the tenon has to be cut to a size that is very close to being too small. (chuck jaws nearly closed up completely) Larger sized tenons depend on the corners of the jaws, and varying density of the wood, they bite in unevenly and grip it off-center.

I use a template to accurately mark the tenon size. I cut close to the line, creating a rough tenon. I continue shaping and refining the bowl from the bottom to the top of rim. Before I remove it, I make the final cuts on the tenon. With a sharp spindle gouge, I cut the line with a slight dovetail angle, and cut a flat shoulder flat to meet it. Usually when I flip a piece, I tighten the jaws just enough to hold it, then I bring up the tailstock (with a scrap between) to provide some pressure. I lock the spindle and spin the blank in the chuck just slightly to make sure there is good solid contact between the shoulder and jaw faces, and then tighten the chuck.
 
Your description of the problem tells me the tenon is not properly seated into the chuck, and the large blank comes out of the chuck when coring. #4 Stronghold profiled jaws expand to 5-3/4", sufficient for coring a 13"x10" blank. Profiled jaws grip extremely well when expanded (vs dovetail or serrated). I can think of 2 very cheap things to help with seating the tenon in the chuck. 1) Are you using the TS livecenter point in the blank center hole to locate and then seat the tenon shoulder to the chuck jaws? This doesn't help lift the blank, but will ensure it is properly seated.

2) To lift the blank, place a small inner-tube under the blank (I use a small one from HF (https://www.harborfreight.com/13-in-inner-tube-with-straight-stem-69439.html). For $7 it's worth a try. With an air chuck with lever and bleed valve (similar to this https://www.harborfreight.com/dual-head-air-chuck-inflator-with-dial-gauge-63544.html) height of the blank is easily controlled.
 
Last edited:
I do 20-25 inch bowls regularly. I core whenever possible. I start with a oneway 6 in faceplate attached to the blank face (future bowl hollow side) using the tailstock work the outside of the bowl blank till satisfied and turn the tenon at the same time. Ensure the center point of the tenon is well marked for later use. For blanks this large I use #5 0r #6 stronghold jaws. Turn blank around, core and wait about 1 year to finish (bummer but necessary) Realize that the bowl blank will warp ,maybe even go oval. the second turning will require rounding the tenon again hence the well marked center point I jam chuck the bowl blank with the tenon on the tailstock side re-round the tenon, reverse the blank using a chuck now and turn a bowl. Hope this is understandable and helps. Ray
I was a little leery of buying the #5 jaws; I worried the aluminum jaws wouldn't hold sufficiently. I have the profiled, serrated jaws now, which seem to compress the tenon too much. The blank was likely 80lbs or more to start, just too heavy for the #3 jaws to hold the tenon. I was glad to be outside the line of fire. I don't leave enough for an expanding hold; I always felt like it was a weaker hold.
Your description of the problem tells me the tenon is not properly seated into the chuck, and the large blank comes out of the chuck when coring. #4 Stronghold profiled jaws expand to 5-3/4", sufficient for coring a 13"x10" blank. Profiled jaws grip extremely well when expanded (vs dovetail or serrated). I can think of 2 very cheap things to help with seating the tenon in the chuck. 1) Are you using the TS livecenter point in the blank center hole to locate and then seat the tenon shoulder to the chuck jaws? This doesn't help lift the blank, but will ensure it is properly seated.

2) To lift the blank, place a small innertube (I use a small one from HF (https://www.harborfreight.com/13-in-inner-tube-with-straight-stem-69439.html). For $7 it's worth a try. With an air chuck with lever and bleed valve (similar to this https://www.harborfreight.com/dual-head-air-chuck-inflator-with-dial-gauge-63544.html) height of the blank is easily controlled.
I was using the tailstock to center the blank when reversing it, and kept the tailstock support for as much of the hollowing as possible. I gave up on the bowl after a big catch made the bottom unfixable. Life is too short to turn crappy wood after all. Chalk that up to learning curve. I have had problems coring big bowls before, because I didn't want to deal with the faceplate/glueblock method. Now it's time to learn some basic skills that I've never mastered.
Did you predrill for the center pin for the big bite? I routinely turn 18” diameter bowls and have never had one fly off the lathe with the same setup.
I don't predrill the center pin. This lets me adjust the blank's orientation with the tailstock if I need to. I love using the big bite. I've never had a piece come off or get loose with it. I do chisel off the bark to get a good grip with it. But I quit using faceplates after buying it. Also, I wait until the bowl is absolutely finished to turn away the mark from the live center, so that I can align it right after finishing the inside.
 
Heavy blanks can be a challenge to get mounted singlehandedly, but I've discovered a couple tricks that make it easier. I have a couple choices of drive options available: An Elio drive and a big spur drive that fits into my 50mm chuck jaws. I have no recollection of who made the spur drive or where I got it, but it tends to get more use because the Elio requires use of an Allen key to bury the pointed machine screws. (I keep thinking I should replace them with pointed flange bolts and keep the proper size Gear Wrench handy)

For either use of either drive, I start by choosing a center point. Big blanks are too heavy to try to find a balance point, so it's estimated, or if the size of the piece dictates it, the center point is dictated by measurement. It can be on the cut face or the bark side, you just have to start somewhere. It can always be changed/adjusted later. I use a Forstner bit to drill into the blank a bit. This not only provides a solid grip point, but provides a shoulder to sort of "hang" the blank on the drive point, while the other hand brings up the tailstock.

As far as your piece not running true when you flip it around, are you making a random size tenon? I used to see chuck jaws as having a range of allowable sizes, which is true, but to flip a piece and have it run true, (or very close) the tenon has to be cut to a size that is very close to being too small. (chuck jaws nearly closed up completely) Larger sized tenons depend on the corners of the jaws, and varying density of the wood, they bite in unevenly and grip it off-center.

I use a template to accurately mark the tenon size. I cut close to the line, creating a rough tenon. I continue shaping and refining the bowl from the bottom to the top of rim. Before I remove it, I make the final cuts on the tenon. With a sharp spindle gouge, I cut the line with a slight dovetail angle, and cut a flat shoulder flat to meet it. Usually when I flip a piece, I tighten the jaws just enough to hold it, then I bring up the tailstock (with a scrap between) to provide some pressure. I lock the spindle and spin the blank in the chuck just slightly to make sure there is good solid contact between the shoulder and jaw faces, and then tighten the chuck.
I have been less than diligent about ensuring the tenon is close to the size of the closed chuck jaws. I know that it grips better this way. I am about to purchase the #5 jaws to increase my flexibility. I need to come up with a way to remove the stuck screws on my chuck jaws. I don't like having to change jaws and don't feel like buying another chuck; I have 4 nova chucks and 2 strongholds. It may be time to fork over some cash for another chuck body.
 
For getting big stuff onto the lathe, I use a hoist. Very simple, very cheap and works a treat.

This picture of the hoist was a proof of concept with my new hoist. The hoist is mounted on one of the roof girders on a sliding rail, which came off a around the world sailing boat.

As my lathe is on wheels, I just locate it under the timber and mount it, then for turning around I use the hoist again and again until the blank is small enough for me to handle.

I also use Vicmarc Faceplate rings, there are four sizes, they are light but very strong.

View attachment 78764

View attachment 78765

View attachment 78766
I actually bought a hoist to lift big blanks but it wasn't high enough to support the blank completely. I need to figure out a better way to hang the hoist from a beam above the lathe. For the bowl in question, I had my neighbor help mount the blank I was mounting. I've given up on turning it, as it developed some serious cracks. I don't like repairing deep cracks unless I really have to.
 
I've given up on turning it, as it developed some serious cracks. I don't like repairing deep cracks unless I really have to.
Big pieces present a couple of cracking challenges.
1. Absolute wood movement is larger If a 10” bowl is going to shrink a 1/2 inch in one direction a 20” bowl will shrink 1”
Even wall thickness and nice curves become more important.
2. the time on the lathe will be a lot longer. If it takes you 30 minutes to rough turn a 10” bowl it will likely take you 90-120 minutes to rough turn a 20” bowl.
Need to keep the wood from drying on the lathe. Plant mister to keep it wet. Wrap in plastic if you stop for any reason.
 
You could use a faceplate and glue block. I use 6" dovetail jaws for a bowl that size. If you can, especially when using the McNaughton system, make your tenon at least 40 percent of the diameter of your bo

Big pieces present a couple of cracking challenges.
1. Absolute wood movement is larger If a 10” bowl is going to shrink a 1/2 inch in one direction a 20” bowl will 1”
Even wall thickness and nice curves become more important.
2. the time on the lathe will be a lot longer. If it takes you 30 minutes to rough turn a 10” bowl it will likely take you 90-120 minutes to rough turn a 20” bowl.
Need to keep the wood from drying on the lathe. Plant mister to keep it wet. Wrap in plastic if you stop for any reason.
The tree had been on the ground since May, so it had already lost a lot of moisture. I did wrap it in a bag between turning the outside and inside. It took a few hours to hog out the inside, but it moved so much it was a lost cause. The drying checks were not visible at first. It wasn't even that large of a blank, just very heavy. It was kind of tragic; about half the bowl was burl figure. Just too far cracked to be worth fixing.
 
It depends on what you mean by "big". For me, I never turn over about 14 inches since there is a very small market for sizes over that. The biggest one I ever turned came off the lathe at 22 inch diameter. I used a 6 inch face plate for that one. For all the rest, I drill a recess to expand into with my chuck jaws, and I use Vicmark exclusively. I do not like to use the tailstock when turning bowls, and with 14 inch sized blanks, I have never had one come off the lathe, at least not yet. The problem with the spur drive use is that it likes to spin out. I have seen huge spur drives, and one that looked like a porcupine, with a bunch of spikes, and they drive very well. I just find the drilled recess to work much more easily. I use a 2 5/8 inch diameter forstner bit to fit my bigger Vicmark chuck jaws.

robo hippy
 
For getting big stuff onto the lathe, I use a hoist. Very simple, very cheap and works a treat.
I also have a sliding rail with chain hoist. I have put more than 150lbs of wet wood onto the lathe without help. You can use any method you chose to attach the piece to the headstock and tailstock. I use a faceplate, screw, glue block, or cup drives, depending on the needs of the project. I put a 20" diameter x 24" long wet log on cup centers and kept driving the tailstock in as things loosened up. Ended up with the cups an inch into both ends of the log but safely turned it. When it comes time to put a chuck on the tenon and flip the blank around, it is supported with the hoist and spins around with two fingers.
 
I was a little leery of buying the #5 jaws; I worried the aluminum jaws wouldn't hold sufficiently. I have the profiled, serrated jaws now, which seem to compress the tenon too much.
The #5 AL profiled jaws I have work just fine. I’ve used them for blanks as large as 15” dia x 20” long, hollowing without TS support. I’ve cored 15” bowls using them. 15” is as big as I can go inboard (16” swing).

Are your other jaws serrated or profiled, they are different. Serrated will not hold as well expanded as the profiled. Both designs are designed to compress the tenon with the serrations or teeth inside the jaws. The teeth marks realign the work if removed from the chuck, if you keep the same “clocking” (all of my chucks have a “clock mark” where jaws meet, and I mark the tenon to get correct orientation for rechucking).

A thing to look for using either serrated or profiled is that the bottom of the tenon does NOT land on the upward slope of a serration - this will push the tenon shoulder off the top of the jaws, had it happen a few times until I figured out the problem. Also, the outer bottom of the tenon needs to be the same distance around the OD of the tenon, so that a serration is not touching only part of the tenon.
 
Last edited:
The #5 AL profiled jaws I have work just fine. I’ve used them for blanks as large as 15” dia x 20” long, hollowing without TS support. I’ve cored 15” bowls using them. 15” is as big as I can go inboard (16” swing).

Are your other jaws serrated or profiled, they are different. Serrated will not hold as well expanded as the profiled. Both designs are designed to compress the tenon with the serrations or teeth inside the jaws. The teeth marks realign the work if removed from the chuck, if you keep the same “clocking” (all of my chucks have a “clock mark” where jaws meet, and I mark the tenon to get correct orientation for rechucking).

A thing to look for using either serrated or profiled is that the bottom of the tenon does NOT land on the upward slope of a serration - this will push the tenon shoulder off the top of the jaws, had it happen a few times until I figured out the problem. Also, the outer bottom of the tenon needs to be the same distance around the OD of the tenon, so that a serration is not touching only part of the tenon.
All my jaws are profiled. I kind of wish I'd started with Vicmarc chucks and smooth jaws, but the stronghold chucks work quite well. Good to hear that the #5 jaws have worked well for you. I should have mine sometime next week, and have a couple nice chunks of elm ready to try them out. And a nice piece of burl!
 
My lathe has a sliding headstock. I purchased a lift table from Harbor Freight, remove tailstock and banjo, slide headstock to the end of lathe and position wood w/faceplate on spindle. Takes a little practice but once you get the hang of it its really easy. When not used for mounting blanks comes in handy as a small table for use on other projects.
 
Back
Top