platform to stand on?

[Sam Fleisher]

Other than building one, is there a platform out there somewhere to buy that isn't $300 dollars? Sister is too short (about 8 inches) for the table I set the benchtop lathe on and I don't want to cut the legs off the table. I foresee her turning career not being too long.

 

[Brian Gustin]

nail together some 2x8x8 lumber and a bit of 3/4 inch OSB should do the trick, I'd think?

 

[Rick Moreton]

A pallet? If that is too short, 2 pallets screwed together. Top it off with a sheet of plywood if you want to be fancy.

 

[Jim Reynolds]

At the risk of overthinking and therefore over-engineering this you might:
- observe your sister while she is turning to figure out where she puts her feet. Will Lerrums at MASW makes the turning studio platforms extend beyond the headstock and under the bed of the lathe by notching out for the feet under the headstock.
- 8" would probably twist my ankle, or worse, if I stepped off without looking. Perhaps a toe kick around the perimeter would prevent an accident and avoid having your sister end her turning career early because of injury.

Best of luck to you both and safe turning!!

 

[robo hippy]

I did make a platform for shorter turners to use when in my shop. I worry about them falling off the edge and not remembering that they are up in the air a bit.

robo hippy

 

[Jim Holcombe]

Unless the platform covers the rest of your shop, I’d say you’re asking for problems. Cut the legs off or build another bench the right height.

 

[Gabriel Hoff]

nail together some 2x8x8 lumber and a bit of 3/4 inch OSB should do the trick, I'd think?

That's building one I think.....

 

[Sam Fleisher]

Hopefully it ends up being a moot point. Working on these this afternoon and apparently she is the decorator/director/dictator? and I'm the peon running the lathe etc..

The walnut one ended up 20 inches tall with his hat.

 

[Jim Holcombe]

You’ve got my luck Sam!

 

[Gerald Lawrence]

I built one for our club as the wheels on lathe added too much height. I painted the perimeter red to remind step.

 

[Mike Novak]

For my grandkids I used 4 layers of 2” thick pink foam board from Home Depot with duct tape to hold them together. Very light and easy to move out of the way when not needed.

 

[Mark Jundanian]

For my grandkids I used 4 layers of 2” thick pink foam board from Home Depot with duct tape to hold them together. Very light and easy to move out of the way when not needed.

"Pink Wood" does dent when an adult stands on it, but I wonder if a cover sheet of, say, 1/4" plywood would address that issue? Admittedly a "build it" solution, but simple enough.

 

[John Jones]

Other than building one, is there a platform out there somewhere to buy that isn't $300 dollars? Sister is too short (about 8 inches) for the table I set the benchtop lathe on and I don't want to cut the legs off the table. I foresee her turning career not being too long.

I think you might be looking for this,
$49.01 in Little Rock
Platform Step, X-Large Steel, Internet # 306535693
Model # JQ-S150
UPC Code # 866326000106

 

[John Jones]

I think you might be looking for this,
$49.01 in Little Rock
Platform Step, X-Large Steel, Internet # 306535693
Model # JQ-S150
UPC Code # 866326000106

Sorry, that's at Home Depot

 

[Sam Fleisher]

Sorry, that's at Home Depot

Thanks for the link. So far her enthusiasm is running out. (fingers crossed) But that looks handy for other things.

For some reason it's $54.45 in Peoria. go figure.

 

[Bill Alston]

Emma Cook (The Tiny Turner) is a professional wood turner and seems to manage ok. She’s 4ft 10 inches tall.

Demo by Emma Cooke (aka ‘The Tiny Turner’) | Cheshire & North Wales Woodturners Association

www.cnwwa.org.uk

 

[Bill Boehme]

Hopefully it ends up being a moot point. Working on these this afternoon and apparently she is the decorator/director/dictator? and I'm the peon running the lathe etc..

Problem solved. As a professional procrastinator, I have found that most problems resolve themselves without my interference. I have a couple Harbor Freight hydraulic carts. Sometimes I put my Jet mini lathe on one of them and then adjust the height as needed.