Mine's pretty fancy - you may not want to go to this much trouble
View attachment 71729
I jammed a length of copper pipe in a spare nozzle and added some duct tape.
That looks good for dust. Do those long small nozzles get clogged up with chips?
-
November 2025 Turning Challenge: Wall Hanging! (click here for details) -
Sign up for the 2025 AAW Forum Holiday Swap by Monday, November 24th (click here for details) -
Congratulations to Konstantin Gusev for "The Nutcracker" being selected as Turning of the Week for November 17, 2025 (click here for details) -
Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.
Compressed air at the lathe: where to place it?
- Thread starter John Whitley
- Start date
That looks good for dust. Do those long small nozzles get clogged up with chips?
Look for 'computer attachments' or 'small attachments' sized for shop vacs. Like these:
Steve, does having been a building engineer fit that qualification? Coors Light please.
Dave Landers
Beta Tester
Mine will clog right at the end, so I just take it out of the hollow form and yank off the chips. Still gets the chips out
Usually only a problem for wet side-grain forms where you get long curls.
Occasionally but just at the tip.
Sure! One Coors Light, coming right up.
I made an adapter to use some stainless steel tube in the nozel for my shop vac. It gets used for all sorts of things including vacuum sealing.
I did a search looking for how other folks run air to their lathe and came across your picture. Great looking turning area!
I realize this is an older thread, but there are some good comments here, so I thought I would respond to them. I have always thought the same thing about blowing things off. I am going to have air near my lathe in my new shop set-up for vacuum chucking and will have a quick disconnect for a hose, but I would rather vacuum saw dust rather than blow it all over the shop.
After buying the shop from the widow of a woodturner/friend/neighbor, I was running some additional circuit wiring thru the attic and found lots of shards of shattered PVC pipe on top of the insulation layer. One piece even penetrated the steel pole barn siding. Must've been one hell of a bang. I wish he was still around to ask him if he was there when it let go.
I used 3/4 and 1/2" sweat-fit copper water piping for my compressor at home. I ran a couple drops in my basement workshop, and one out to my garage. I had planned something similar in my barn shop, but so far, I've just run a 50' rubber hose alongside my dust collection piping to near the lathe.
I have 8' ceiling in my shop space, but instead of hanging a shop light over the lathe, I build a large plywood box/shelf for over the lathe. It has LED tubes on the underside, and a generous shelf for chucks, paper towels, stereo receiver, etc. It also gives a "wall" space at each end for hanging tools and a track on the back for dust collection hose drop. It's not pretty, but effective.
I used 3/4 and 1/2" sweat-fit copper water piping for my compressor at home. I ran a couple drops in my basement workshop, and one out to my garage. I had planned something similar in my barn shop, but so far, I've just run a 50' rubber hose alongside my dust collection piping to near the lathe.
I have 8' ceiling in my shop space, but instead of hanging a shop light over the lathe, I build a large plywood box/shelf for over the lathe. It has LED tubes on the underside, and a generous shelf for chucks, paper towels, stereo receiver, etc. It also gives a "wall" space at each end for hanging tools and a track on the back for dust collection hose drop. It's not pretty, but effective.
I was going to suggest the same. I have had a 25 foot retract reel for about 15 years so when turning I can pull out enough hose for the purpose and hook the nozzle near to hand.