I'm looking for a face plate to fit the Union Graduate bowl turning lathe. Hoping to find a 6 or 8" RH plate. If you happen to have any Graduate stuff please let me know.
-
December 2025 Turning Challenge: Single Tree! (click here for details) -
Congratulations to Bob Henrickson, People's Choice in the November 2025 Turning Challenge (click here for details) -
Congratulations to John Dillon for "Chinquapin Oak" being selected as Turning of the Week for December 22, 2025 (click here for details) -
Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.
WTB Face plate 1 1/2 x 6 Union Graduate
- Thread starter David Shumaker
- Start date
If you can't find one Best Wood Tools carries a variety of face plates.
Say they will machine one to suit if they don't carry the size you want.
Might give them a call.
(931) 456-6155 or (931) 788-0429
Say they will machine one to suit if they don't carry the size you want.
Might give them a call.
(931) 456-6155 or (931) 788-0429
Thanks John. I'll give him a call. Getting anything for this machine here in the USA is difficult.
This one has both L/H and R/H threads for inboard and outboard turning
www.beaufortink.co.uk
Unless you are trying to minimise how far the faceplate comes out from the headstock, why not use a direct threaded chuck and use a faceplate ring attached to that. If you don't have one already, a chuck is far more versatile with different jaws
www.facebook.com
150mm woodturning lathe faceplate - 1 1/2 inch x 6 tpi Dual L/R thread
Versachuck woodturning lathe faceplates,150mm woodturning lathe faceplate - 1 1/2 inch x 6 tpi Dual L/R thread
www.beaufortink.co.uk
Unless you are trying to minimise how far the faceplate comes out from the headstock, why not use a direct threaded chuck and use a faceplate ring attached to that. If you don't have one already, a chuck is far more versatile with different jaws
Log into Facebook
Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com
Thanks for your reply Neil. The chuck looks very nice but I have a vintage New Zealand made Nova with a ton of jaws that came with the lathe. I'm after a faceplate just to get the rough wood balanced and a tenon on safely. Unfortunately the tailstock moves a bit even when locked down. Normally I just hold a piece between centers but this flaw makes that difficult. The whole machine is a project. Thanks so much for your help!
Yikes, slipping? I wonder why. (Is this the locking problem discussed in a fairly recent post?)
JKJ
It's not slipping. The live center moves due to wear in the threaded portion of the tailstock. I need to get that replaced or take it to a machinist to have it repaired. A video would explain more but I can't seem to find it on my phone.
Rats, that sounds like a more complicated problem, one I haven't encountered. I've worked on the insides of several tailstocks for people but they were stuck rather than slipping! On one PM3520 the quill was warped for some reason. I can't even imagine how that happened.
Can your old Nova chuck take a screw center? I have faceplates for all my lathes, but rarely use them. Most of my bowls I start out with on a screw Chuck, unless it's a natural edge bowl, then I would use a spur drive. Still it's a good idea to have a faceplate, I hope you can locate one.
I do have a screw center for the chuck. It has always been my practice to use the tail center for extra security when using one. Ultimately the tailstock will need repaired. The faceplate would allow pieces to be turned securely without a tailstock in place. Mr. Jordan told me that Sorby manufactures a plate for the Graduate. That will likely be the way I go. Thanks for your input. Honestly I hadn't considered the screw center.
What does your tailstock need to be repaired? I agree about the screw chuck. I almost never use a screw chuck without the tailstock.