Any machine shop could make up an adapter for a salvaged motor from scratch. You may be able to start with a shaft adapter from McmasterCarr.
-
January 2026 Turning Challenge: Turned and Bent! (click here for details) -
Congratulations to Phil Hamel, People's Choice in the December 2025 Turning Challenge (click here for details) -
Congratulations to Clayton Thigpen for "Armillary Sphere" being selected as Turning of the Week for January 19, 2026 (click here for details) -
Welcome new registering member. Your username must be your real First and Last name (for example: John Doe). "Screen names" and "handles" are not allowed and your registration will be deleted if you don't use your real name. Also, do not use all caps nor all lower case.
Looking for input from those mechanical/engineering minds
- Thread starter Jim Grieco
- Start date
You don’t need a powered solution at all. Instead, glue a portion of a wide sanding belt to a flat substrate to make a sanding slab, then turn your partial vessel upside-down and move it around by hand. A few swipes will even out high spots quickly.
Tim
Tim
I've done that already and not happy with the results.
Think vertical lathe. Build a potters wheel. Small motor to keep weight down, pulleys to step speed down, and a shaft that will accept a chuck.
Or find a cheap used lathe and pull the headstock to create the potters wheel.
Or find a cheap used lathe and pull the headstock to create the potters wheel.
HE DOESN'T WANT A LATHE!
It’s no longer a lathe when just the headstock is used and oriented vertically. It’s a potters wheel.HE DOESN'T WANT A LATHE!
Last edited:
Then put a circular platen on a vertical-shaft gear motor similar to my sharpening machine shown here:
Tim
An actual potter's wheel might work nicely - they are almost always variable speed and should be enough torque. A pro potter friend uses multiple wheels. Might find an inexpensive on on Facebook, etc or from a retiring potter or potter heir. It should be easy to mount any kind of a spindle adapter or even a simple threaded rod to hold the chuck.
The problem with a repurposed potter's wheel might be access to the work since the wheels often have wide, round trays. But with the motor and speed control it should be trivial to adapt it to provide clearance for any sanding need.
JKJ
The problem with a repurposed potter's wheel might be access to the work since the wheels often have wide, round trays. But with the motor and speed control it should be trivial to adapt it to provide clearance for any sanding need.
JKJ
Howdy Jim, An interesting dilemma. I know you said you do not have room for another lathe but what about locating a used small mini lathe and removing the headstock? The headstock could be mounted on a bench or a small platform similar to Paul's great idea above. Rotisserie motors pop into my mind (for assembling a finishing station) but they usually go much slower than the 250 rpm you would like. Best of luck!
I would say skip the motor drive and the sandpaper.
Mount a shaft with the 1-1/4" adaptor on bearings and put a large handwheel on the outboard end.
Make a flat bed out of something like MDF add an adjustable stop at 90 degrees to the spindle.
Mount a router on a fixture like is used often used to detail turnings (John Lucas could provide photos).
The cut would not need to be very deep and if not deep enough it should be evident how much more is necessary and not more than about .020".
Your left hand on the handwheel and your right-hand moving the router against the stop guide.
The 2 most important considerations are no runout on the spindle and the 90 degree stop guide.
Mount a shaft with the 1-1/4" adaptor on bearings and put a large handwheel on the outboard end.
Make a flat bed out of something like MDF add an adjustable stop at 90 degrees to the spindle.
Mount a router on a fixture like is used often used to detail turnings (John Lucas could provide photos).
The cut would not need to be very deep and if not deep enough it should be evident how much more is necessary and not more than about .020".
Your left hand on the handwheel and your right-hand moving the router against the stop guide.
The 2 most important considerations are no runout on the spindle and the 90 degree stop guide.